Choosing A Cell Disrupter

	BioSpec Products, Inc. (800) 617-3363 or (918) 336-3363

Choosing a High-throughput Cell Disrupter

To date there are four High Throughput Bead Mill Cell Disrupters on the market capable of using 96-well microplates: The MiniBeadbeater-96, the Model 2000 Geno/Grinder, the Talboys Homogenizer and the Retsch MM 300. A fifth alternative, commercial paint shakers, have proven to be unacceptable for most applications. The shaking motion of paint shakers rotate or resonate about a central axis, thus giving non-homogeneous cell disruption across the microplate platform.

When "shopping" for a commercial High Throughput Cell Disrupter there are several important features to consider. Sample capacity and price are obvious considerations, of course, but one should also look at vial orientation during shaking (vials with the axis oriented horizontally and the shaking action in a like direction are ials held in an upright position and shaken in an up and down motion). High shaking speeds and adequate shaking distances are also important. Compromise on the later two properties in the shaker and it can take up to 10X longer to get cell disruption. Perhaps the most important consideration is high shaking energy (for example, see "Retsch MM 300 vs. BioSpec MBB-96", below).

Another, less essential but desirable feature is the capability to shake both vials and microplates on the same machine. And, look for an efficient, easy-to-use plate or vial clamping mechanism. Microplates should be clamped into a holder designed to press the entire surface area of the mat or membrane to the surface of the microplate.

A comparison. Retsch MM 300 vs. BioSpec MBB-96: The BioSpec Products MBB-96 is a much more powerful shaker than the Retsch MM 300 - compare a 1288 watt motor versus 184 watt motor. In addition, it is significantly less expensive - compare $4100 versus $7500 (or more). Our MBB-96 cell disrupter has a two year warranty and, being made in the USA, can be quickly serviced, if needed.

From a performance standpoint, the high power of our MBB-96 cell disrupter assures complete cell breakage in about three minutes using low cost glass or ceramic beads. Because of this superior shaking energy it does not require the use of heavier, more expensive (and sometimes contaminating) stainless steel or tungsten carbide beads. While less energetic machines will disrupt cells, it takes much longer to get equivalent good cell disruption (we know because we built weaker machines in the course of developing the final MBB-96!). If extracting nucleic acids, we counsel our users to do the cell disruption directly in the nucleic acid extraction media, thus shortening extraction time and eliminating possible degradation of the RNA or DNA. Extraction media can be prepared "in house" or purchased from various commercial "kit" manufacturers. The MBB-96 holds either 48 standard microtubes (which can be kept cold in a solid aluminum block, if necessary), one 2 ml 96-deepwell microplate, two 1ml 96-deepwell microplates, or four standard sized microplates.

Bottom line: The MBB-96 is more powerful, faster acting, and sells at a lower price. Sample capacity is equal to or exceeds that of competitive machines. BioSpec Products, the company who first introduced the "beadbeating" technique for cell disruption into the laboratory twenty-six years ago, is a quality source for technical expertise and prompt service.

Comments from a Researcher at Lawrence Livermore National Lab*:

"We have now tested the MiniBeadBeater-96 with two different sets of samples, with more than 100 samples processed. It seems to perform comparably with the single channel units we have from BioSpec, which is a very pleasant surprise. We are able to isolate DNA from purified Bacillus spores, which have proved to be too difficult for all of the other commercially available, multi-channel instruments we have tried."

*Not to be taken as an endorsement by LLNL or its affiliates.

.....from Ontario Veterinary College:

"We received your MiniBeadbeater and put it to use immediately. It is just as advertised, easy to use, and our tissue homogenization and resultant RNA isolation has improved drastically!!

.....from Steve @emu.edu:

I'm shopping around for a bead-beater kind of homogenizer, and the
mini-bead beater 16 looks great, price-wise anyway, compared to
the qbiogene Fastprep, and other similar products.

A couple of questions:
1. How does it compare to the other >$7000 bead beaters on the
market and why is it so much cheaper? For over 30 years our philosophy has been to offer novel scientific equipment at reasonable prices. This BioSpec accomplishes in two ways: 1) We can often design and build equipment around preexisting mass marketed tools and appliances, thus benefiting price-wise by economy of scale. Examples are the TissueTearor and the BeadBeater. 2) For product promotion we rely mostly on word-of-mouth and literature references. Advertising and other forms of marketing and promotion can be extremely expensive . We advertise but only modestly. In most cases, product promotion can constitute over 50% of the final sales price of scientific equipment!